{"product_id":"330703-000-040-10-02-00-bently-nevada-3300-xl-11-mm-probe","title":"330703-000-040-10-02-00 | Bently Nevada | 3300 XL 11 mm Probe","description":"\u003cp\u003eConfigured for high-range displacement sensing in machine monitoring systems, the \u003cstrong\u003eBently Nevada 330703-000-040-10-02-00\u003c\/strong\u003e (\u003cstrong\u003e330703\u003c\/strong\u003e 11 mm Proximity Probe) provides direct physical execution of vibration and shaft position measurements. This probe is designed for applications requiring a larger sensing area and increased linear range compared to standard 8 mm probes, maintaining the high-frequency response necessary for effective rotor dynamics analysis.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e330703-000-040-10-02-00\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eNot specified\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e40 mm case length; 1.0 m cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-51 deg C to +177 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive component\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Tip Diameter\u003c\/td\u003e\n\u003ctd\u003e11 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eEddy-Current Probe Scaling and Gap Voltage Validation\u003c\/h3\u003e\n\u003cp\u003eThe 11 mm transducer system utilizes an eddy-current probe scaling optimized for the larger tip geometry, typically providing a linear range greater than standard 5 mm or 8 mm probes. During installation, the gap voltage must be validated at the Proximitor sensor output; technicians should target a -10 VDC reading at the linear center of the operating range. Proper cross-talk suppression is required when multiple probes are installed in proximity; failure to maintain minimum separation distances or shielding integrity will result in induced signal interference.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the 330703 11 mm probe be used with a standard 8 mm Proximitor sensor?\u003c\/p\u003e\n\u003cp\u003eA: No. The Proximitor sensor must be specifically calibrated for the 11 mm probe geometry to maintain the correct linear scale factor and electrical impedance match. Mixing mismatched components introduces significant measurement nonlinearity.\u003c\/p\u003e\n\u003cp\u003eQ: What is the purpose of the ClickLoc connector?\u003c\/p\u003e\n\u003cp\u003eA: The ClickLoc connector is a miniature coaxial interface designed to ensure a consistent, low-resistance electrical connection. It provides a tactile indication of proper mating and maintains the characteristic impedance of the transmission line.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProbe Gap Setting\u003c\/strong\u003e: Thread the probe into the mounting assembly until the desired gap is achieved, then secure it using the locking nut. Ensure the tip is centered over the target surface to avoid signal distortion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShielding\u003c\/strong\u003e: Maintain the continuity of the coaxial shield throughout the cable run. The shield should be grounded only at the Proximitor sensor terminal block to prevent ground loops.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Care\u003c\/strong\u003e: Inspect the ClickLoc interface for cleanliness before mating. In high-vibration environments, ensure the connector protector is fully engaged to prevent accidental disconnection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Routing\u003c\/strong\u003e: Adhere to the minimum bend radius of 25.4 mm (1.0 inch). Do not subject the coaxial cable to excessive pulling force, which could damage the internal dielectric and shift the electrical impedance.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":53575978909880,"sku":"330703-000-040-10-02-00","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0935\/6132\/3704\/files\/330103-00-07-10-02-00__2_bc99cb8d-e414-420e-a704-13a441db7f2e.jpg?v=1781061677","url":"https:\/\/www.globalpetroparts.com\/products\/330703-000-040-10-02-00-bently-nevada-3300-xl-11-mm-probe","provider":"Global Petro Parts Automation","version":"1.0","type":"link"}