{"product_id":"ge-is200eacfg3abb-excitation-ac-feedback-board","title":"GE IS200EACFG3ABB Excitation AC Feedback Board","description":"\u003cp\u003eConfigured for AC signal scaling and isolation in the EX2100 excitation control architecture, the \u003cstrong\u003eGE IS200EACFG3ABB\u003c\/strong\u003e (\u003cstrong\u003eIS200EACF\u003c\/strong\u003e Excitation AC Feedback Board) provides direct physical execution of high-voltage attenuation and low-level analog signal output to control modules.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel Brand\u003c\/td\u003e\n\u003ctd\u003eGE IS200EACFG3ABB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.42 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e280 mm x 180 mm x 30 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 degC to +60 degC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 5 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSignal Input Range\u003c\/td\u003e\n\u003ctd\u003eUp to 600 V AC phase-to-phase\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Signal Range\u003c\/td\u003e\n\u003ctd\u003e0–10 V DC scaled\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIsolation Voltage\u003c\/td\u003e\n\u003ctd\u003e1500 V AC RMS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eChannels\u003c\/td\u003e\n\u003ctd\u003e3-phase AC sensing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication and Firmware Flash Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe IS200EACFG3ABB interfaces directly with the EX2100 backplane bus, supporting deterministic data transfer rates aligned with the control processor cycle. Firmware revisions are bound to specific EX2100e hardware builds; mismatched flash loads will result in boot refusal. Hardware identification resistors encode the board type to the controller, preventing incorrect module substitution.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can this board be hot-swapped in an operational EX2100 rack?\u003c\/p\u003e\n\u003cp\u003eA: No. Removal or insertion must occur only with the associated power section de-energized to prevent backplane transients.\u003c\/p\u003e\n\u003cp\u003eQ: What is the effect of using an incorrect firmware load?\u003c\/p\u003e\n\u003cp\u003eA: The controller will halt initialization and log a firmware mismatch fault; operation will not proceed until correct firmware is installed.\u003c\/p\u003e\n\u003cp\u003eQ: Does the board support channel-to-channel isolation?\u003c\/p\u003e\n\u003cp\u003eA: No. Isolation is provided between the high-voltage inputs and the control electronics, but not between individual sensing channels.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eInstall the IS200EACFG3ABB into the designated EX2100 rack slot using anti-static handling procedures. Ensure all AC input wiring is routed separately from low-voltage control cabling to minimize inductive coupling. Tighten terminal screws to 0.6 N·m and verify torque after initial energization. Confirm shielding continuity at both ends of signal cables, grounding only at the rack chassis point to avoid ground loops.\u003c\/p\u003e","brand":"GE Fanuc","offers":[{"title":"Default Title","offer_id":53601519730872,"sku":"IS200EACFG3ABB","price":1325.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0935\/6132\/3704\/files\/IS200EACFG3ABB-3.jpg?v=1781753272","url":"https:\/\/www.globalpetroparts.com\/products\/ge-is200eacfg3abb-excitation-ac-feedback-board","provider":"Global Petro Parts Automation","version":"1.0","type":"link"}