{"product_id":"is200ectbg1ade-exciter-contact-terminal-board-ge","title":"IS200ECTBG1ADE Exciter Contact Terminal Board | GE","description":"\u003cp\u003eConfigured for excitation control interfacing in Mark VI and Mark VIe Speedtronic turbine control systems, the \u003cstrong\u003eGE IS200ECTBG1ADE\u003c\/strong\u003e (base model \u003cstrong\u003eIS200ECTB\u003c\/strong\u003e) provides direct physical and electrical execution between field contact wiring and internal I\/O packs. Signal routing occurs via hardened terminal blocks and shielded interconnects, supporting discrete contact input acquisition and breaker status monitoring without protocol translation.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel Brand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric (GE)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e0.45 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e280 mm x 160 mm x 25 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-30 degC to +65 degC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 5 W (passive board, no active power draw)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSystem Compatibility\u003c\/td\u003e\n\u003ctd\u003eMark VI \/ Mark VIe Speedtronic\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Type\u003c\/td\u003e\n\u003ctd\u003eBarrier terminal blocks, ribbon\/D-shell cables\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication and Firmware Flash Considerations\u003c\/h3\u003e\n\u003cp\u003eThe IS200ECTBG1ADE interfaces directly with Mark VIe I\/O packs over a deterministic backplane bus. Bus communication velocity is fixed at system clock rate; no user-adjustable parameters exist. Firmware flash compatibility is governed by the assigned I\/O pack processor type and must match the control system’s release baseline to prevent configuration rejection during download. Mismatched firmware will halt signal mapping until corrected.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the IS200ECTBG1ADE be hot-swapped?\u003c\/p\u003e\n\u003cp\u003eA: No. All field wiring and control system power must be removed prior to removal or installation to avoid damaging connected I\/O electronics.\u003c\/p\u003e\n\u003cp\u003eQ: Does the board require calibration after replacement?\u003c\/p\u003e\n\u003cp\u003eA: No calibration is required; verification is limited to contact continuity checks and correct terminal torque application.\u003c\/p\u003e\n\u003cp\u003eQ: Is the board compatible with both Mark VI and Mark VIe systems?\u003c\/p\u003e\n\u003cp\u003eA: Yes, provided the associated I\/O pack and system firmware support the same hardware revision level.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eMount vertically in the designated control cabinet channel using factory-specified sheet metal brackets. Torque terminal screws to 0.8 Nm unless otherwise stated by site standards. Maintain separation between high-voltage field wiring and low-level signal leads to reduce inductive coupling. Ground shield terminations at the panel entry point only, ensuring continuous shield integrity without intermediate breaks. Verify all circuits are de-energized before termination.\u003c\/p\u003e","brand":"GE Fanuc","offers":[{"title":"Default Title","offer_id":53601510097080,"sku":"IS200ECTBG1ADE","price":1588.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0935\/6132\/3704\/files\/IS200ECTBG1ADE-3.jpg?v=1781752667","url":"https:\/\/www.globalpetroparts.com\/products\/is200ectbg1ade-exciter-contact-terminal-board-ge","provider":"Global Petro Parts Automation","version":"1.0","type":"link"}