{"product_id":"mark-vie-aegis-power-group-board-ge-is200aepgg1a","title":"Mark VIe Aegis Power Group Board GE IS200AEPGG1A","description":"\u003cp\u003eConfigured for ground fault detection and power distribution management in GE Mark VIe and EX2100 excitation systems, the \u003cstrong\u003eGE IS200AEPGG1A\u003c\/strong\u003e (\u003cstrong\u003eIS200AEPG\u003c\/strong\u003e Aegis Power Group Board) provides direct physical execution of voltage isolation and signal conditioning tasks within turbine control architectures.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel Brand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric (GE)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eApprox. 0.45 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard Mark VIe Single-Slot Module\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 degC to +60 degC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHumidity\u003c\/td\u003e\n\u003ctd\u003e5% to 95% non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eBackplane Powered (Refer to System Manual)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePrimary Function\u003c\/td\u003e\n\u003ctd\u003eGround Fault Detection, Voltage Isolation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Bus Communication and Firmware Flash Compatibility\u003c\/h3\u003e\n\u003cp\u003eThe IS200AEPGG1A interfaces with the Mark VIe control rack via the standard backplane connector. Data exchange and diagnostic reporting occur over the IONet deterministic network. Firmware revisions must match the host controller's compatibility matrix; mismatched firmware can result in communication timeouts or failure to pass self-test diagnostics during rack initialization.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the IS200AEPGG1A support hot-swapping?\u003c\/p\u003e\n\u003cp\u003eA: No. The board contains CMOS components susceptible to electrostatic discharge and electrical transients. Always de-energize the control panel and follow ESD protocols before removal or insertion.\u003c\/p\u003e\n\u003cp\u003eQ: What is the function of the onboard LEDs?\u003c\/p\u003e\n\u003cp\u003eA: The LEDs provide real-time status for power presence, ground fault detection, and active communication link status, allowing for localized troubleshooting without software intervention.\u003c\/p\u003e\n\u003cp\u003eQ: Is this board compatible with the older Mark VI series?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the IS200AEPGG1A is compatible with both Mark VI and Mark VIe systems, provided the rack configuration supports the AEPG functional designation.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eESD Protection:\u003c\/strong\u003e Wear a grounded wrist strap at all times. Handle the board only by the edges to avoid contact with IC pins or solder points.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMechanical Seating:\u003c\/strong\u003e Ensure the module is fully seated into the rack guide rails before tightening the securing screws. Do not force the connector.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTorque Specifications:\u003c\/strong\u003e Apply standard torque values to terminal block connections if external wiring is present. Verify no loose strands exist in the terminal wells.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding Verification:\u003c\/strong\u003e Confirm that the rack chassis is properly earth-grounded prior to applying power to prevent false ground fault alarms.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"GE Fanuc","offers":[{"title":"Default Title","offer_id":53601520910520,"sku":"IS200AEPGG1A","price":1325.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0935\/6132\/3704\/files\/IS200AEPGG1A-3.jpg?v=1781753512","url":"https:\/\/www.globalpetroparts.com\/products\/mark-vie-aegis-power-group-board-ge-is200aepgg1a","provider":"Global Petro Parts Automation","version":"1.0","type":"link"}